Water-based synthetic resin, with very fine particles.

High deformability thixotropic mineral smoothing adhesive, very high bonding, resistant to the action of water.

Thixotropic, water-resistant, mineral smoothing adhesive with excellent finish.

Thixotropic, water-resistant, mineral smoothing adhesive with excellent finish.

Thixotropic, water-resistant, mineral smoothing adhesive with excellent finish.

Lightweight, highly deformable, high-strength smoothing adhesive with low thermal conductivity.

White heat insulation panel cut from block on straight edge, made of sintered expanded polystyrene (EPS).

White heat insulation panel cut from block on straight edge, made of sintered expanded polystyrene (EPS).

Grey block-cut heat insulation panel with straight edge; it is made from a block of Neopor® (EPS with graphite additive) cut with hot wire.

Grey block-cut heat insulation panel with straight edge; it is made from a block of Neopor® (EPS with graphite additive) cut with hot wire.

Printed grey embossed and laminated heat insulation panel; it is made from a block of Neopor® (EPS with graphite additive).

Block cut heat insulation panel; it is made from a block in Styropor® (white EPS) and Neopor® (graphite-added EPS) cut with hot wire.

Heat-insulating panel with embossing and breakage cuts; it is made from a block of Neopor® (EPS with graphite additives, obtained from renewable raw materials derived from biomass) and coated with white EPS.

Mineral rock wool panel, CAM and EDP certified; provides an excellent combination of winter and summer thermal insulation.

Panel in mineral glass wool G3, breathable, eco-friendly; certified CAM and EDP; water repellent and high density.

Printed panel embossed high resistance to compression, designed for the zoccolature.

Aerogel nanotech insulation panel, coupled to breathable polypropylene membrane reinforced with glass fiber.

Percussion plug 8 mm hole with a pre-assembled nail in the socket.

Percussion plug 8 mm with premounted nail in the plug shaft.

Percussion plug 8 mm with premounted nail in the plug shaft.

Vite per tassello a rondScrew for washer dowel made of galvanized steel for fixing insulating panels on wooden supports.

Washer dowel, chip screw nail for fixing insulation panels on wooden supports with cap for reducing thermal bridges.

Kit consisting of:

• Polyamide helical dowel.
• Steel adjustment helical bar.
• Cap cover closure in EPS.

Neopor® (EPS with graphite additive) seal cover

Technological network of glass fibre coated with high protection against alkalis.

Reinforcement net in glass fiber 155g/m² with surmounted by 10 cm thinned.

Aluminium starting profile with pre-arranged end section and drip tray.

Kit modulare realizzato in pvc e rete in fibra di vetro, composto da supporti di varie dimensioni.

Horizontal and vertical closing profile made of prepainted aluminium.

Joint element made of rigid rubber, used to join the starting bases horizontally, preventing their detachment.

Impact pin with steel nail for fixing to the wall of the starting base.

Spacer for compensation of defects flatness starting bases.

Aluminium roof profile used to protect the insulation panel at the window sill and the window sill.

Profile of recovery made of aluminium, used to protect the lower insulating panel in correspondence with the connection between panels of different thicknesses.

Profile shaped “V” made of prepainted aluminum in grey with pre-drilled edges, to be inserted into the scalanature of the insulating panels.

Shaped profile made of PVC and glass fibre mesh, to be inserted into the grooves of insulating panels with heat-sealed glass fibre mesh.

Profile shaped in pvc to be inserted into the scalanature of the insulating panels.

White fiberglass corner mesh for the bottom of the walls.

White mesh for reinforcement of the corners of openings in thermal insulation systems.

Open corner corner with white heat-sealed fiberglass mesh, made of PVC fiberglass.

Corner “arrow” with heat-sealed fiberglass mesh, made of PVC and fiberglass mesh.

Corner “open-angle” with heat-sealed fiberglass mesh, made of PVC and fiberglass mesh.

PVC corner with heat-welded glass fiber mesh at the angle of an arc.

Corner “protruding” locket with heat-welded glass fiber net.

Coin “L-shaped” windbreaker with heat-sealed fiberglass mesh.

Corner with drip profile, for starting base in aluminium and heat-welded glass fibre net.

Profile with 4 mm PE self-adhesive tape, made of PVC and heat-sealed fiberglass mesh.

Plaster closure profile, of different thicknesses, with heat-welded glass fibre net.

Joint profile with central body in flexible rubber and heat-sealed glass fibre net, with accessory to achieve a clean installation.

Cylindrical support in high density EPS used for the insertion of elements of medium load.